Toyota Camry

1992-1997 of release

Repair and car operation

Kamri's Toyota
+ General data
- 1. Maintenance
   1.2. Periodicity of service
   - 1.3. Maintenance
      + 1.3.1. Each 400 km or weekly
      + 1.3.2. Each 5 000 km or 3 months
      - 1.3.3. Each 10 000 km or 6 months Type A Type B Check of a free wheeling and height of installation of a pedal of coupling
         - Check and accumulator service
   Battery charging
         + Check and replacement of a driving belt
         + Check of tightness of hoses and effluence of liquids Check of system of cooling Change of provision of installation of tires
      + 1.3.4. Each 25 000 km or 12 months
      + 1.3.5. Each 50 000 km or 24 months
      + 1.3.6. Each 100 000 km or 48 months
+ 2. Engine
+ 3. Six-cylinder V6 engines
+ 4. Major maintenance of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. Ignition system
+ 8. Toxicity fall
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment Check and accumulator service



The electrolit in the storage battery represents poisonous and corroding acid. Therefore it is necessary to avoid electrolit hit in eyes, on the skin, the painted surfaces and so on. In case of flood of electrolit wash out a denny place plentiful amount of cold water. If the electrolit got to eyes, after washing of eyes by water, immediately address to the doctor.

At operation of the storage battery hydrogen therefore never it is impossible to smoke or address with open fire or scintillating substances in close proximity to the accumulator is formed.

Always prior to the beginning of work on electric equipment disconnect minus a wire from the storage battery. It will prevent emergence of unintentionally short circuits.

Never disconnect wires from the storage battery at the working engine.

Always disconnect wires from the storage battery if the charging of the storage battery with use of the external charger is made.

Always disconnect wires from the storage battery and a wire from the generator for the period of car repairs with use of devices of electric welding.

At existence in a code radio receiver against theft, an accumulator detachment, check that you have connection codes.

On models since 1993 the system of an airbag of safety is disconnected, if the accumulator is disconnected for long term. If a control lamp of a safety cushion it lights up and necessary to burn after repeated connection of the accumulator, it is necessary to address in специализи a rovanny workshop for restoration of operability of system.

Tools and materials necessary for service of the accumulator
1–the guard necessary in order that of electrolit did not get in a face;
2–soda. The soda diluted in water, is necessary for neutralization of the poured electrolit;
3–vaseline. It is used for protection of plugs of the accumulator against corrosion;
4–wire brush. It is necessary for removal of traces of corrosion from plugs of the accumulator and wires;
5–plastic washers. Are established on the accumulator under plugs of wires;
6–stripper. It is used for removal of plugs from the accumulator;
7–a version of the wire brush used for cleaning of plugs of the accumulator;
8–rubber gloves which are necessary for using at work with electrolit

Removal of the plug of a wire from the accumulator

1. Before the beginning of service of the accumulator gather all necessary tools and materials.
2. Purity of the storage battery and, in particular, its top surface is especially important, as the layer of dirt collecting on it easily forms electrocarrying-out routes which lead to the battery self-category. Purity is important not only for a served battery room of the battery, together with for the unattended battery which, despite the name, is not absolutely unattended. 3. Using a metal brush, clear plugs аккумуля a Torah and plugs of wires. If necessary wash out plugs soda solution in warm water. Be careful, that solution of soda did not get to accumulator banks.
4. Cleaning of plugs of the accumulator make before emergence of light brilliant metal. 5. Check that nuts of a fixing element of the accumulator are reliably tightened. Do not draw a nut as the case of the accumulator can be damaged.
6. Before connection of clips of the accumulator grease plugs with acid-free vaseline and an anticorrosive compound.