Toyota Camry

1992-1997 of release

Repair and car operation



Kamri's Toyota
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
+ 4. Major maintenance of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. Ignition system
+ 8. Toxicity fall
+ 9. Transmission
- 10. Automatic transmission
   10.2. General information
   + 10.3. Diagnostics
   + 10.4. Adjustment and replacement of a cable of a choice of transfers
   10.5. Check and adjustment of a cable of management by a butterfly valve
   + 10.6. Check, replacement and adjustment of the switch of blocking of a starter
   + 10.7. Lock of blocking of the lever of a choice of transfers
   + 10.8. Replacement of sealing rings
   - 10.9. Check and replacement of support of a transmission
      10.9.1. Removal
      10.9.2. Installation
   10.10. Electronic control system
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment



10.9.1. Removal

GENERAL INFORMATION

Arrangement of bolts of fastening of a protective plate on the four-cylinder engine

Arrangement of bolts of fastening of a protective plate on the six-cylinder engine

PERFORMANCE ORDER
1. Remove a cowl.
2. Remove pressure in fuel system.
3. Remove a weight wire from the accumulator.
Preventions

At existence in a code radio receiver against theft, before a detachment of the accumulator check that you have connection codes.

On models since 1993 the system of an airbag of safety is disconnected, if the accumulator is disconnected for long term. If a control lamp of a safety cushion it lights up and necessary to burn after repeated connection of the accumulator, it is necessary to address in a specialized workshop for restoration of operability of system.


4. Disconnect the electric socket and remove the executive mechanism cruise control.
5. Remove the accumulator and an accumulator support.
6. Remove an air inlet and a casing of the air filter. Disconnect from the engine топливопроводы and close them jams.
7. Remove the fuel filter and an arm of the fuel filter.
8. Remove the charcoal canister together with an arm.
9. Remove a tank of a washer of a windscreen and a broad tank.
10. Disconnect an accelerator cable from a control lever a butterfly valve.
11. Mark and disconnect all vacuum hoses, hoses of cooling liquid, electric sockets and grounding tires.
12. Remove the fan of a radiator and a fan casing. Merge cooling liquid from cooling system, remove a radiator and disconnect hoses from a heater.
13. Disconnect a cable of a choice of transfers from the lever of a choice of transfers.
14. Lift the car and fix on supports. Remove wheels.
15. Disconnect a reception exhaust pipe from a final collector.
16. Remove mudguards.
17. Merge engine oil.
18. Remove driving belts.
19. Merge oil from a transmission.
20. Disconnect hinges of power shafts from a transmission.
21. On models with the amplifier of a steering unscrew bolts of fastening of the pump of the amplifier of a steering and move the pump aside, without disconnecting from it hoses.
22. On models with central air of air unscrew bolts of fastening of the compressor of the conditioner and move it aside, without disconnecting from it hoses.
23. Disconnect hoses from an oil radiator of a transmission and immediately close them jams. On models with four-cylinder engines remove the oil filter and an oil radiator. For access to a drive plate гидротран a sformator unscrew bolts and remove a protective plate (see fig. An arrangement of bolts of fastening of a protective plate on the four-cylinder engine and fig. An arrangement of bolts of fastening of a protective plate on the six-cylinder engine). Unscrew 6 bolts of fastening of a plate of a drive to the hydrotransformer, thus for access to bolts of fastening turn a cranked shaft.
24. Hook on the engine together with a transmission cargo lifting by the ny mechanism and raise so that the weight of the engine was perceived by the load-lifting mechanism.
25. Unscrew bolts of fastening of support of the power unit.
26. Being careful, slowly take the engine together with a transmission from a motor compartment of the car.
27. Lower the power unit on wooden whetstones and establish so that under a transmission it was possible to establish a jack.
28. Remove a starter.
29. Supporting a transmission a jack, unscrew bolts of fastening of a transmission to the engine.
30. Move a transmission from the engine and remove it. Thus be careful, that the hydrotransformer did not act in film from an entrance shaft of a transmission.
31. Remove the hydrotransformer from an entrance shaft of a transmission.