Toyota Camry

1992-1997 of release

Repair and car operation


Kamri's Toyota
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
+ 4. Major maintenance of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. Ignition system
+ 8. Toxicity fall
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
- 12. Brake system
   12.2. General information
   12.3. Anti-blocking system of brakes (ABS)
   12.4. Replacement of brake shoes of disk brakes
   + 12.5. Support of disk brakes
   + 12.6. Brake disk
   12.7. Replacement of brake shoes of drum-type brakes
   + 12.8. Working brake cylinder
   + 12.9. Main brake cylinder
   12.10. Brake pipelines and hoses
   12.11. Pumping of hydraulic brake system
   + 12.12. Vacuum amplifier of brakes
   12.13. Replacement of brake shoes of the hand brake on back disk brakes
   + 12.14. Adjustment of the parking brake
   + 12.15. Replacement of a cable of the hand brake
   + 12.16. Stoplight switch
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment



12.13. Replacement of brake shoes of the hand brake on back disk brakes
GENERAL INFORMATION
Preventions

Surely make replacement of all blocks even if the limit of wear were reached by one block.

At work of brake shoes the brake dust which contains asbestos is formed, unhealthy therefore when cleaning brake shoes do not use the compressed air and do not inhale a dust.

Details of the hand brake on back disk brakes
1–brake disk;
2–spring;
3–spring clamps;
4–spring;
5–adjusting level;
6–forward brake shoe;
7–pin;
8–plate;
9–spring; 		10-rack of blocks;
11-laying;
12-back block;
13-pin;
14-springs;
15-back support;
16-stopper;
17-fastening bracket;
18-lever of the hand brake

PERFORMANCE ORDER
1. Remove a brake disk.
2. Measure thickness of brake shoes. If thickness of an overlay of a brake shoe it is necessary to replace less than 0,8 mm, brake shoes.
3. Remove a nave and the nave bearing.
4. Using special liquid, clear brake shoes. 5. Disconnect a returnable spring of a back brake shoe from an anchor finger. 6. Disconnect a returnable spring from a back brake shoe.
7. Remove a returnable spring of a forward brake shoe from an anchor finger. 8. Remove a returnable spring from a forward brake shoe. 9. Remove a plate of a spring of fixing of a back brake shoe, pressing a plate and turning it on 90 °.
10. Remove a rack of blocks from the top part of brake shoes. 11. Remove a plate of a spring of fixing of a forward block, pressing a plate and turning it on 90 °.
 12. Remove регулировоч a ny level and the bottom returnable spring.
13. Remove a bracket of fastening of a sharnirny finger from a back brake shoe. 14. Remove the lever of the hand brake from a back brake shoe. 15. Put a layer of high-subjects of peraturny greasing on a brake board in places of contact of a board with blocks.
16. Establish the lever of the hand brake on a back brake shoe and fix a bracket. 17. Fix a returnable spring from a reverse side of a back brake shoe. 18. Fix a returnable spring from a reverse side of a forward brake shoe.
19. Establish регулировоч a ny level between brake shoes. 20. Establish brake shoes on a brake board and establish a rack of blocks and a spring. 21. Establish a returnable spring of a forward brake shoe.
22. Establish a returnable spring of a back brake shoe. 23. Establish a spring and a clamp of a back brake shoe. 24. Establish a spring and a clamp of a forward brake shoe.
25. The correct arrangement of details of the hand brake on a brake board.
26. Establish a brake disk.
27. Take a stopper from an adjusting opening of a brake disk. Rotating a screw-driver a wheel of an adjusting level, dissolve brake shoes so that it was possible to remove a brake disk without jamming.
28. Further installation is made in sequence, return to removal.