Toyota Camry

1992-1997 of release

Repair and car operation


Kamri's Toyota
+ General data
+ 1. Maintenance
+ 2. Engine
- 3. Six-cylinder V6 engines
   3.2. General information
   3.3. The repair which is not demanding removal of the engine
   + 3.4. Top dead point (VMT) of the piston of the first cylinder
   + 3.5. Cover of a head of the block of cylinders
   + 3.6. Inlet collector
   3.7. Final collector
   - 3.8. Gear belt and pulleys
      3.8.2. Check
      3.8.3. Installation
   3.9. Replacement of a forward sealing ring of a cranked shaft
   3.10. Replacement of sealing rings of camshafts
   + 3.11. Camshafts and pushers
   + 3.12. Head of the block of cylinders
   + 3.13. Oil pallet
   + 3.14. Oil pump
   3.15. Drive flywheel / plate
   3.16. Replacement of a back sealing ring of a cranked shaft
   3.17. Suspension bracket of the power unit
+ 4. Major maintenance of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. Ignition system
+ 8. Toxicity fall
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment



3.8. Gear belt and pulleys

3.8.1. Removal
GENERAL INFORMATION
Preventions

At existence in a code radio receiver against theft, before a detachment of the accumulator check that you have connection codes.

On models since 1993 the system of an airbag of safety is disconnected, if the accumulator is disconnected for long term. If a control lamp of a safety cushion it lights up and necessary to burn after repeated connection of the accumulator, it is necessary to address in a specialized workshop for restoration of operability of system.

Elements of a drive of the mechanism of a gazoraspredeleniye
1–pulley of a cranked shaft of a driving belt;
2–right engine mount;
3–top casing of a gear belt;
4–laying;
5–gear belt;
6–single pulley No. 2;
7–pulley of the right camshaft;		 8–pulley of the left camshaft;
9–pulley of a cranked shaft;
10-directing a gear belt;
11-single pulley No. 1;
12-mechanism of a tension of a gear belt;
13-dustproof cover;
14-bottom casing of a gear belt

PERFORMANCE ORDER

1. Remove a weight wire from the accumulator.

2. Remove cooling liquid from a broad tank and liquid from a tank of a washer of a windscreen.

3. Remove the executive mechanism cruise control and the vacuum pump.
4. Remove driving belts from the generator and the pump of the amplifier of a steering.
5. Lift a forward part of the car and fix on supports. Remove the right forward wheel.
6. Remove protection of an arch of the right forward wheel.
7. On the engine 3VZ-FE remove a tank of liquid of the amplifier of a steering, without disconnecting from it hoses, and move it aside.
8. Support the engine a jack and remove the right suspension bracket of the power unit with an arm.
9. Unscrew spark plugs.
10. Remove the top casing of a gear belt together with laying.
11. Establish the piston of the first cylinder in VMT in a compression step.
12. Check existence of adjusting labels on a gear belt. If labels are erased, and the gear belt will be repeatedly устанав ливаться, put on it labels.
13. Check that adjusting labels of pulleys the distributor of ny shaft are combined with indexes. 14. Remove the mechanism of a tension of a gear belt.
15. Reduce a tension of a gear belt between pulleys of camshafts, turning a back pulley clockwise.

16. If the gear belt is repeatedly established, put a label on outer side of a gear belt at level of the upper edge of the bottom casing of a gear belt.
17. Remove a gear belt from pulleys of camshafts.
18. If pulleys of camshafts are worn-out or damaged, replace them. For this purpose uncover heads of the block of cylinders, fix a wrench a camshaft from a provorachivaniye and unscrew a bolt of fastening of a pulley. Remove a pulley from a camshaft.
19. Remove the top single pulley.
20. Unscrew a bolt of fastening of a pulley of a cranked shaft, thus a screw-driver for teeths of a gear wreath of a flywheel fix a cranked shaft from a provorachivaniye.
21. After unscrewing of a bolt of fastening of a pulley of a cranked shaft check that the label on a pulley is combined with figure 0 on the index.
22. Remove a pulley of a driving belt from a cranked shaft.
23. Remove the bottom casing of a gear belt with laying.
24. Remove a gear belt from a pulley of a cranked shaft.
25. If the belt is repeatedly established, check combination of labels on a gear belt and a pulley of a cranked shaft.
26. Remove the bottom single pulley.
27. Remove a pulley of a cranked shaft.