Toyota Camry

1992-1997 of release

Repair and car operation



Kamri's Toyota
+ General data
+ 1. Maintenance
+ 2. Engine
- 3. Six-cylinder V6 engines
   3.2. General information
   3.3. The repair which is not demanding removal of the engine
   + 3.4. Top dead point (VMT) of the piston of the first cylinder
   + 3.5. Cover of a head of the block of cylinders
   + 3.6. Inlet collector
   3.7. Final collector
   - 3.8. Gear belt and pulleys
      3.8.2. Check
      3.8.3. Installation
   3.9. Replacement of a forward sealing ring of a cranked shaft
   3.10. Replacement of sealing rings of camshafts
   + 3.11. Camshafts and pushers
   + 3.12. Head of the block of cylinders
   + 3.13. Oil pallet
   + 3.14. Oil pump
   3.15. Drive flywheel / plate
   3.16. Replacement of a back sealing ring of a cranked shaft
   3.17. Suspension bracket of the power unit
+ 4. Major maintenance of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. Ignition system
+ 8. Toxicity fall
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment



3.8.3. Installation

PERFORMANCE ORDER
1. Check that the label on a pulley of a cranked shaft is combined with a ledge on the case of the oil pump (And) and establish a clamp of a pulley and a bolt (In).
2. On a carving of a bolt of fastening of the bottom single pulley put the means interfering unscrewing of a bolt, establish the bottom single pulley and fix it a bolt, having tightened a bolt the demanded moment.
3. Establish a gear belt on a pulley of a cranked shaft and the bottom single pulley. Thus combine labels on a gear belt and a pulley of a cranked shaft.
4. Establish directing a gear belt to a pulley of a cranked shaft.
5. Establish the bottom casing of a gear belt with laying.
6. Establish on a cranked shaft a pulley of a driving belt and fix a bolt, thus hold a cranked shaft from a provorachivaniye.
7. Establish the top single pulley and fix it a bolt, having tightened it the demanded moment.
8. Establish a pulley of a gear belt on the left camshaft, and the adjusting pin of a camshaft should enter into pulley dredging. Holding a camshaft from a provorachivaniye a wrench, screw up a bolt of fastening of a pulley of a camshaft.
9. Repeatedly check combination of adjusting labels.
10. Check that the adjusting pin right the distributor a foot of a shaft is above. Otherwise uncover heads of the block of cylinders and a wrench turn a camshaft so that the label on a pulley of a camshaft was combined with the index on a back casing of a gear belt.
11. Turn a pulley of the left camshaft clockwise on one tooth. Establish on a pulley a gear belt and turn a pulley in a starting position.
12. Establish a pulley on the right camshaft. Thus the adjusting pin of a camshaft should enter into pulley dredging.
13. Fix a pulley a bolt, thus a wrench hold a camshaft from a provorachivaniye.
14. Establish a gear belt on a camshaft pulley. If the gear belt is used repeatedly, combine earlier made labels.
15. Using a press or a vice, slowly press a pusher of the mechanism of a tension of a gear belt into the case and fix it in this situation by a steel core, having inserted it through an opening in the case of the mechanism of a tension and a pusher.
16. Establish the top casing of a gear belt.
17. Further installation is made in sequence, return to removal.