Toyota Camry

1992-1997 of release

Repair and car operation

Kamri's Toyota
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
- 4. Major maintenance of engines
   4.2. General information
   4.3. Compression check
   4.4. Recommendations about engine removal
   + 4.5. Removal and engine installation
   4.6. Sequence of dismantling of the engine
   4.7. Dismantling of a head of the block of cylinders
   + 4.8. Cleaning and survey of a head of the block of cylinders
   4.9. Assembly of a head of the block of cylinders
   4.10. Removal of pistons with rods
   4.11. Removal of a cranked shaft
   + 4.12. Block of cylinders of the engine
   4.13. Pistons and rods
   4.14. Cranked shaft
   + 4.15. Survey and choice of radical and shatunny bearings
   4.16. Control люфта balance weight assemblies (engine 5S-FE)
   4.17. Engine balance of assembly at major maintenance
   4.18. Installation of piston rings
   + 4.19. Installation of a cranked shaft and check of working gaps of bearings
   4.20. Installation of a back sealing ring of a cranked shaft
   4.21. Installation of pistons and rods, check of working gaps of bearings
   4.22. Installation of assembly of the balance weight (engine 5S-FE)
   4.23. Engine start after major maintenance
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. Ignition system
+ 8. Toxicity fall
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment

4.4. Recommendations about engine removal

GENERAL INFORMATION

Details of the six-cylinder V6 3MZ-FE engine (the engine 3MZ-FE is similar to the shown engine 1MZ-FE except for the oil pallet)

1–masloslivny stopper;
2–laying;
3–oil pallet;
4–partition of the oil pallet;
5–cover of radical bearings;
6–persistent half rings of a cranked shaft;
7–cranked shaft;
8–mesh oil filter;
9–laying;
10-oil pump;
11-forward sealing ring of a cranked shaft;
12-sealing ring of round section;
13-arm of a single pulley;
14-bypass pipe of system of cooling;
15-sensor of pressure of oil;
16-clip;
17-drainage hose;
18-connector;
19-lock ring;

20-piston finger;
21-spring of a piston ring;
22-first kompressionny ring;
23-second kompressionny ring;
24-maslosjemny rings;
25-piston;
26-top plug of a rod;
27-rod;
28-rod bearing;
29-bottom cover of a rod;
30-back basic plate;
31-flywheel;
32-back sealing ring of a cranked shaft;
33-back cover of a cranked shaft;
34-arm of the oil filter;
35-radical bearings;
36-back plate;
37-drive plate;
38-forward plate

Main details четырехци lindrovy engine

1–masloslivny stopper;
2–laying;
3–oil pallet;
4–mesh filter;
5–laying;
6–partition of the oil pallet;
7–covers of radical bearings;
8–persistent half rings of a cranked shaft;
9–cranked shaft;
10-laying;
11-oil pump;
12-forward sealing ring of a cranked shaft;
13-right suspension bracket of the power unit;
14-elastic element of a suspension bracket;
15-rod cover;
16-rod bearing;
17-rod;

18-lock ring;
19-piston;
20-second kompressionny ring;
22-first kompressionny ring;
23-maslosjemny piston rings;
24-piston finger;
25-rod plug;
26-block of cylinders;
27-laying;
28-back basic plate;
29-flywheel or drive plate;
30-back sealing ring of a cranked shaft;
31-back cover of a cranked shaft;
32-radical bearings;
33-drive plate;
34-back plate;
35-forward plate

If you decided to remove the engine for repair, some preparations should be made.

The paramount importance has a choice of a venue of works, for providing space for service and storage of spare parts. It is desirable to do it at autostation or in garage with an equal horizontal floor with a pure firm covering.

Before removal of the engine wash up the engine and a motor compartment. Removal of the engine needs the load-lifting mechanism allowing safely to lift the power unit.

If you remove the engine for the first time, it is necessary to invite the skilled expert. Besides, there are many cases when one person cannot execute at the same time all actions at engine removal.