Toyota Camry

1992-1997 of release

Repair and car operation



Kamri's Toyota
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
- 4. Major maintenance of engines
   4.2. General information
   4.3. Compression check
   4.4. Recommendations about engine removal
   - 4.5. Removal and engine installation
      4.5.1. Removal
      4.5.2. Installation
   4.6. Sequence of dismantling of the engine
   4.7. Dismantling of a head of the block of cylinders
   + 4.8. Cleaning and survey of a head of the block of cylinders
   4.9. Assembly of a head of the block of cylinders
   4.10. Removal of pistons with rods
   4.11. Removal of a cranked shaft
   + 4.12. Block of cylinders of the engine
   4.13. Pistons and rods
   4.14. Cranked shaft
   + 4.15. Survey and choice of radical and shatunny bearings
   4.16. Control люфта balance weight assemblies (engine 5S-FE)
   4.17. Engine balance of assembly at major maintenance
   4.18. Installation of piston rings
   + 4.19. Installation of a cranked shaft and check of working gaps of bearings
   4.20. Installation of a back sealing ring of a cranked shaft
   4.21. Installation of pistons and rods, check of working gaps of bearings
   4.22. Installation of assembly of the balance weight (engine 5S-FE)
   4.23. Engine start after major maintenance
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. Ignition system
+ 8. Toxicity fall
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment
вакансии - Москва



4.5.1. Removal

PERFORMANCE ORDER
1. Remove pressure in fuel system.
2. Remove a weight wire from the accumulator.
3. Remove the accumulator and an accumulator support.
4. Remove a sheeting on wings and a cowl and remove a cowl.
5. Remove a casing of the air filter.
6. Lift the car and fix on supports. Merge cooling liquid from system of cooling and engine oil. Remove driving belts.
7. Mark, then disconnect all vacuum lines, hoses, electric sockets, tires of grounding and fuel lines.
8. Remove a tank for liquid of a washer of a windscreen and a broad tank.
9. Remove radiator fans, a casing and a radiator.

10. Disconnect hoses of supply of cooling liquid to a heater.

11. Remove residual pressure in a fuel tank for what remove a stopper of a bulk mouth, then disconnect топливоп роводы from the engine and close them jams.
12. Disconnect a cable of management of a butterfly valve and draft of management of a transmission.
13. Take a plait of wires from fastening brackets to a lobby and the left side of the engine and a transmission.
14. On cars with the amplifier of a steering unscrew bolts of fastening of the pump of the amplifier of a steering and move it aside, without disconnecting hoses.
15. On models with central air of air unscrew bolts of fastening of the compressor of the conditioner and move it aside, without disconnecting hoses, and using a soft wire, tie up it to a body.
16. Disconnect a reception exhaust pipe from a collector.
17. On models with the four-cylinder engines, equipped with the oil radiator established between the oil filter and the block of cylinders, remove the oil filter and disconnect hoses from an oil radiator.
18. Hook on the engine slings of the load-lifting mechanism and raise the engine so that the top of the engine was perceived by the load-lifting mechanism.
19. Remove the right suspension bracket of the power unit. For removal of the right suspension bracket of the power unit remove the hinge (And), unscrew a coupling bolt (In) and remove a suspension bracket of the power unit (C).
20. Unscrew a bolt, fixing a suspension bracket of the power unit (And) to a body from a radiator.
21. On models with an automatic transmission remove a protective plate of the hydrotransformer from a forward part of a transmission. Disconnect the hydrotransformer from a plate of a drive and move it to a transmission case.
22. Unscrew bolts of fastening of a transmission to the engine and separate the engine from a transmission, thus the hydrotransformer should remain in a transmission case. If the engine acts in film together with a transmission, do not unscrew bolts of fastening of a transmission to the engine, and from a transmission disconnect power shafts, wires, hoses, a cable of gear shifting and a speedometer cable.
23. Check that anything, except engine support any more does not connect the engine and a transmission to a car body.
24. Support a transmission a jack through wooden whetstone. Unscrew bolts of fastening of support of the power unit.
25. Slowly lift the power unit from a motor compartment. 26. Move the engine aside from the car and lower on wooden supports on a floor or remove a flywheel/plate of a drive and establish the engine on a special bed.